Whirlpool Washer Not Spinning/Draining | What to Do!

Spread the love

When the Whirlpool Washer is not spinning, it’s a time-consuming process to rule out all possible causes. Our floor is littered with piles of wet laundry, which prompts people to Google ‘why won’t my washer spin’ or ‘why won’t my washing machine spin?’ However, they are not required to waste valuable time in search of an explanation.

Allow us to assist you in troubleshooting your washer so that you can focus on other aspects of your life.

Reasons Why Whirlpool Washer Not Spinning & Solutions!

Consumers have relied on washers to thoroughly clean their clothes for decades. Wash cycles can effectively cleanse fabric and remove dirt using a combination of water and detergent.

Agitation is a critical component of this process because it allows the washing machine to lift and remove settled stains. Agitation enables the washer to thoroughly clean fabrics, resulting in brighter, cleaner whites every time you do laundry!

Your washing machine’s spinning drum serves as the initial step in the draining process. The drum is where drum-style clothes washers remove excess water from clothes and towels before drying them in a dryer.

If the spinning mechanism in your washer is not functioning properly, the washer will not drain. If your Whirlpool washing machine does not spin, a professional technician may need to inspect it. Fortunately, you can easily resolve this issue using our helpful troubleshooting tips.

  • Unbalanced or Clogged Load

Clothes can become tangled in the washer between the drum and the basket, forming a walker.

Unbalanced loads can cause your washer to walk or shudder as it spins. When this occurs, pause the load, open the lid, remove the clothing, and reposition it.

If you are not careful when loading your washing machine, clothes can accumulate on one side of the drum, disrupting the washer’s motion and preventing it from spinning at full speed.

This means that clothes may come out of the washer dripping wet — not an attractive appearance.

If you suspect that your laundry is unbalanced, reorganize your wet laundry and rerun the spin cycle.

  • Equalize the Washer

If your washer is not perfectly level, it will not spin properly. This results in extended cycle times and increased washing frequency—all of which are a waste of your time and money.

Other indicators of an unlevel washing machine include excessive noise and vibration during the spin cycle.

To determine if your washer has a leveling issue, manually turn the dial and ensure that the front of the machine is perfectly level with the floor.

Ascertain that all feet are in contact with the ground. If it is not level, you can level it by adjusting the feet.

  • Washing Machine is Overloaded

If your washing machine is trembling or making loud noises, it is most likely overloaded. A washing machine can only handle a certain number of garments before it begins to fail.

See also  What is the Best Laptop For Case Catalyst Software? SEE HERE!

Assure that your washing machine is not filled to its maximum capacity; moving the load around to distribute the weight evenly across the drum will also help reduce the risk of damage caused by overload.

When attempting to do a large amount of laundry at once, it is common to overload the washing machine. Over time, this can result in loud crashing sounds and even serious damage to your washer.

The solution is straightforward: minimize the amount of laundry you load into the washer during each cycle.

ALSO SEE: Why Is Water Leaking in My Refrigerator?

  • Reset the Washing Machine

If the preceding steps do not resolve the Whirlpool washer not spinning issue, try resetting the machine. To reset your Whirlpool washing machine, follow these steps:

  • Disconnect the washer
  • Select NORMAL on the mode dial.

Turn the dial counter-clockwise one click, three times clockwise, one more time counter-clockwise, and finally one click clockwise again.

  • Drain Hose that is clogged or kinked

If your washer’s drain hose is bent or clogged inside, it will prevent water from draining properly at the end of each cycle.

As a result, you will spend additional time and effort drying your clothes in the dryer, and your machine will age prematurely.

If this occurs, disconnect the washer drain hose from the pump and inspect it for clogs caused by hairballs, coins, or other debris. Additionally, inspect the hose and pump for blockages.

It’s worth checking the drain hose placement twice. If the drain hose is too far down the standpipe, water will not drain from your machine effectively, resulting in an improper drain and plenty of dirty suds to sour your clothes.

The purpose of this section is to inspect the drain hose’s condition. Ascertain that it is in a neutral position and is not twisted or kinked.

  • Interlock & Door Lock

Your washing machine’s door lock prevents the door from being opened while the machine is running.

The door lock system is composed of two components: the machine’s locking mechanism and a catch on the door.

The machine is engaged when it is in use; it disengages when the door is opened.

The locking mechanism of the washer is equipped with a switch that communicates the status of the door to the control board.

Without locking the mechanism, the control board will be unable to initiate spin cycles.

If your washing machine’s door lock is defective, it’s possible that the washer will exhibit certain symptoms, such as Whirlpool washer not spinning.

The washer may fail to lock or the door lock switch may not engage when the machine closes.

Additionally, if a door lock fault code has been confirmed, error codes may be displayed. If any of these problems exist, it is possible that you will need to replace the door lock.

  • Drain Pump Filter Obstruction

The coin trap or drain filter on a Whirlpool is a small plastic piece that sits above the pump. Its purpose is to intercept foreign objects such as coins prior to them entering the drain.

This filter can become clogged with small particles over time, obstructing water drainage. When your machine does not drain properly, it may be due to a clogged filter.

See also  What is Whitewood at Lowes & Home Depot? SEE HERE!

Please remove the access panel located on the front bottom of your Whirlpool washer. Once you’ve located the drain filter, cleaning it effectively should take no more than two minutes.

After cleaning, run a hot wash to completely clear the machine of any debris that may have remained.

Whirlpool Washer Not Spinning

  • Affecting the Lid Switch

Numerous older top-loading machines incorporate a lid switch as a safety precaution to ensure proper spinning function. The machine will not spin if the lid is not properly closed.

If the washer is equipped with this type of switch, an additional piece of metal will be mounted beneath the washer lid.

When the metal pin is inserted into the hole in this piece of metal, which serves as a magnetic field sensor, the switch is activated.

Ascertain that the lid switch is mechanically activated. If it is not, then the switch may have a mechanical issue, and replacing it will resolve the issue.

If, on the other hand, the lid switch is activated but no power is supplied to the motor during the spin or drain cycles, the lid switch is most likely defective.

  • Drive Belt Has Become Worn Out

When a Whirlpool washer refuses to spin, the most common cause is a broken drive belt. The drive belt is located at the machine’s base and is connected to the pump that circulates the washing water.

Examine this belt visually and feel for cuts or cracks; if it is damaged, it must be replaced.

Remove the washer’s plug and pull it away from the wall to gain access to the machine’s back.

Because the belt is located at the bottom of the tub, you will need to pull on a pair of gloves to unlatch the washing machine’s bottom panel.

Following the removal of the old belt, thread the new one through the pulley and secure it. Plug in your machine and turn it off.

  • Drain Pump Faulty

If your Whirlpool washer is not spinning properly, the pump should be checked. It may be clogged with debris or may be defective and require replacement.

Disconnect the drain line and remove the back panel of your machine to inspect the pump.

Examine the area for debris with a flashlight or a special tool. If there is debris in the pump or if you have other reasons to believe it is defective, you will need to replace it — the pump is not a repairable component and must be purchased new.

If the drain pump is not blocked, check to see if it is operating properly by using a multimeter to verify that it is receiving power. Verify that both connectors on the pump are receiving power.

Although multimeter readings vary by model, a resistance of between 5 and 10 ohms across both terminals indicates that the drain pump is operational. If an incorrect reading is displayed, unplug the washer and replace the drain pump.

  • Examine The Drain Hose (Not Common Issue)

The drain hose connected to the back of your washing machine is the next item to inspect.

If this hose is bent or clogged, water will not drain properly and your clothes will come out wet at the end of the cycle.

Disconnect the hose from the drain pump and check to ensure it is not bent. Additionally, check for blockages in both the hose and the drain pump that restrict water flow.

See also  11 Best Shoes for Canada Winter for Cozy, Warm Feet in the Snow

Additionally, it’s a good idea to verify that the drain hose is properly positioned. If the hose is positioned incorrectly inside the standpipe, it can result in improper draining. This results in the Whirlpool washer not completely draining the water.

  • Shift Actuator Failed

Another frequent problem with Whirlpool top loading machines is that the shift actuator has ceased to function properly.

This actuator alternates between agitating and spinning the transmission gears.

However, it is also counting the revolutions of the basket, as it is equipped with a basket speed sensor.

If the washer fails mechanically or electrically, it will remain in the agitating cycle and will not advance to the spin cycle.

  • Whirlpool Speed Sensor Is Not Working

Examine The Coin Collector Or Drain Filter (Common Issue)

Your Whirlpool machine is equipped with what is known as a coin trap or drain filter. If this becomes clogged, your washing machine will be unable to spin dry your clothes.

This component is located close to the pump and acts as a filter, capturing any foreign object that enters the drain. The most frequently left-in objects are small items such as keys, coins, paperclips, pins, and even small socks.

The drain filter is located behind the access panel on the front bottom of your machine. The filter is simple to clean, and once cleaned, the water should drain more freely from the machine.

  • Clutch (Not Common Issue)

If your Whirlpool washer is a direct drive model, the clutch may be failing. The clutch will prematurely wear out as a result of improper washer loading.

You can perform a simple eyeball test by leaning it back and inspecting the area around the gearcase and clutch for signs of oil. Replace the gearcase if there is a significant amount of oil present.

Alternatively, if you’re looking for a more advanced version of the eyeball test, try this:

  • Compress the clutch ring’s spring with pliers.
  • Take it out of the drum
  • Examine the rivet holes that secure the ring pads in place.
  • Replace the clutch if there is a lot of debris in the holes.

Examine the clutch for a glossy, reflective finish. This also indicates that it should be altered.

When inspecting these items, do not remove the outer tub; only the gearcase should be removed.

The washer’s timer or control board failed to operate properly (Not Common Issue)

Finally, if you’ve exhausted all other options on this list, check the washer timer.

Your Whirlpool transmission features a feature known as a neutral stop. This means that the washer is briefly stopped during the spin cycle by a timer to allow the spin to engage.

If your machine does not perform this function, the washer timer is defective and must be replaced.

This can be verified by monitoring the machine as the load drains. After 3 minutes, open and close the lid. If it spins, the timer should be replaced.

Have you ever encountered a similar issue with your Whirlpool washer? What steps did you take to rectify the situation? Do you have any additional questions about the subject? Leave a comment below and we’ll have a discussion.

Author: Howard S. Baldwin

My name is Howard S. Baldwin. I am a work-at-home dad to three lovely girls, Jane + Hannah + Beauty. I have been blogging for the last 3 years. I worked for other Home and Lifetsyle blogs, did hundreds of product reviews and buyers’ guides. Prior to that, I was a staff accountant at a big accounting firm. Needless to say, researching and numbers are my passion. My goal is to be an informative source for any topic that relates to DIY life and homemaking.

Leave a Reply

Your email address will not be published.