A GE washer will not spin properly if the power supply is insufficient or the washer is in need of repair. A broken door lock, a damaged control panel, or a defective timer can all disrupt the spin cycle. The spinning power of the washer will be restored by replacing faulty metal components.
GE washing machines are renowned for their superior quality and durability. Even the best washers, however, will require repair at some point due to age and continuous use.
While this may be unsettling for some, with a little patience and know-how, repairing a GE washing machine is quite simple. With this GE washer repair guide, you can quickly resolve the GE washer not spinning issue.
What Causes GE Washer Not Spinning? Troubleshooting and Diagnosis
It’s easy to overlook the complexity of washers and dryers. They, like your refrigerator or oven, have a network of moving parts, a motor, and a pump.
If something is wrong with it, you are unlikely to be able to repair it at home.
If your washing machine suddenly stops spinning, there are a few non-mechanical items you can check immediately to resolve the issue.
ALSO SEE: Kenmore Dryer Not Heating Up?
If one side of your washer appears to be heavier than the other, a load imbalance may develop, preventing the LG washer from spinning.
When you have a load of laundry to wash, it is critical that your clothes are distributed evenly throughout the drum — otherwise, the drum will not spin properly!
When users attempt to clean delicate clothing on a fast cycle while using bulky towels or clothes on the opposite side, an imbalance load occurs, resulting in clothes being tossed around and pounded against the inner tub, accompanied by loud thumping sounds while the machine is in use.
This shuts down the machine and alerts you to the problem, preventing mechanical damage. Close the lid, then reopen it and spread your clothes out before resuming.
Equalize the Washer
If your washing machine is not leveled properly, it will not operate at maximum capacity or efficiency. If you suspect your washer is unbalanced, look for additional warning signs such as excessive noise and vibration during the wash cycle.
To ensure that your washer is level, place a carpenter’s level on top of it and look for five points that are all level. If an incomplete line is visible or if one of the endpoints is higher than the other, your machine must be leveled.
Adjusting each individual leg in the front and back until the machine is completely balanced is the process.
If your washer is not fully loaded, it may tip the machine off balance and cause it to spin inefficiently. A machine that is overloaded will almost certainly have the same effect. Obviously, a washer that is not properly loaded can generate additional noise.
Overloading your washing machine can result in it performing poorly and breaking down prematurely. This results in costly, unnecessary repairs — which is why you should only wash the amount of clothing recommended at any given time.
Always check your machine’s weight capacity before loading — with this information, you’ll be able to fill it comfortably while keeping an eye on how much laundry you’re actually doing.
Master Reset to Factory Settings
If the machine does not spin, you have two options: reload it and restart it, or drain it and perform a master reset.
Unplug the machine and open the door to drain it. Once it has drained sufficiently, close the door and reconnect the plug.
Unplug the washer and open and close the door six times in 12 seconds to perform a master reset. Each washer will have its own unique reset mechanism.
If none of the fixes listed above resolves your issue, it’s time to consult a professional.
Clogged Drain Trap
Front-load washers are well-known for their capacity to clean a large amount of laundry efficiently. Regrettably, they also collect more lint than top-load machines do during the washing process.
If you notice your drain trap is overflowing or your machine is spinning slower than usual, it may have become clogged over time and ceased to spin entirely.
Occasionally, regardless of how diligent you are, the drain filter system will become clogged with food particles or other debris. If the drain filter system becomes too clogged to function properly, the washer will shut down and notify you that the drain filter system needs to be cleaned.
Unplug the machine, drain the water, clean the drain of any lint or debris, and then reconnect the drain pump. Otherwise, the water may overflow, causing damage to your home.
Once you’re certain that everything is in order, reconnect the power and allow the washer to resume its spin cycle. Check to see if the GE washer not spinning problem persists or not.
Examine the Lid Switch
On top-loading washing machines, the lid switch is located beneath the main lid. The lid switch acts as a safety feature, preventing the machine from operating while the main lid is opened. The machine comes to a halt when the lid is opened.
You will be unable to wash clothes or operate your washing machine if this safety device fails. If the GE washer is not spinning, try closing and opening the lid first; if that does not work, check to see if the lid switch is broken.
If your GE washer will not spin, verify that the lid switch is mechanically activated. If it is, inspects the washer to determine if any levers are stuck or if any actuators are damaged.
A faulty switch will render the motor inoperable even when the lid activates it mechanically. If none of these checks reveal anything, the lid switch will need to be replaced.
Control Water Levels
To begin, unplug the washer and the control wires. Then, using an ohmmeter, check these areas for continuity.
With no water in the tub, continuity should exist between terminals 7 and 15.
With a full tub, continuity should exist between terminals 7 and 16.
If none of these readings are obtained, the control is defective and must be replaced.
Examine the Water Pump
If your washing machine does not spin but continues to agitate, there is a good chance that the water pump is malfunctioning. The pump is responsible for extracting water from the drum and redistributing it throughout the wash.
The washing machine will not begin spinning until all of the water in the drum has been drained.
Pumps become clogged from time to time and frequently develop problems as they age.
If your washing machine makes an unusual noise or drains slowly, the problem may be with the pump. Unplug it and inspect it for blockages, such as lint or fabric softener sheets. If no visible signs of damage or clogging exist, it is necessary to replace the pump.
Broken Drive Belt
When the drive belts on front-load and top-load washers are worn out, the baskets will not spin.
These belts are responsible for moving your washing machine’s agitator and spinning basket.
They regulate the agitator’s and wash load’s motion and contribute to the drum’s overall rotation.
A worn belt can cause your washer to skip a cycle or even fail to start at all. While a qualified repair person can easily replace the belt, you should also listen for any sounds indicative of a belt problem; squeaking or other noises could indicate that the belt is stretched, loose, or damaged.
If your washer is making an excessive amount of noise, it’s time to replace the belt to resolve the GE washer not spinning problem.
Examine the detergent’s composition:
Ascertain that you are using the appropriate type. Detergent is a critical component of the cleaning power of your washing machine.
If you’re using a powdered detergent, ensure that it says “Washing Machine” or “Dry Cleaner” on the label. Unless specifically instructed to do so by a repair technician, do not use any other type of detergent.
To obtain the correct type of detergent for your washing machine, you may need to consult your dealer or visit an appliance parts store.
Following that, add the recommended amount of detergent to the dispenser of your washing machine according to the package directions.
Check the detergent level
One of the most common causes of a GE washing machine that will not spin is a low detergent level. Many people use less detergent than the manufacturer recommends and then wonder why their washing machine does not work properly.
Indeed, certain washing machines require more detergent than others due to their intricate design.
Therefore, check the instructions included with the detergent you’re using to ensure you’re using the correct amount.
Verify the water type
Ensure that the water is hard (not soft). Calcium and magnesium are present in soft water, which has an effect on the cleaning process.
Consider the following: If your water is excessively soft, it acts as a lubricant between the clothes and the washer drum. This causes the washer to wear out more quickly and spin less efficiently.
On the other hand, hard water contains fewer minerals and is therefore more effective at removing soil from clothing. Additionally, it assists in keeping your washer running longer and extends its life.
Ensure that the water is the proper temperature
The temperature of the water in the majority of washing machines is controlled by an automated thermostat. However, you should verify this with the manual.
Almost certainly, you will need to adjust the temperature of the water slightly.
For instance, if your water is too hot, turn it down a few degrees. If the temperature is too low, increase it by a few degrees.
When adding the detergent, the washing machine must reach a temperature of at least 40°C (104°F). If the water is too cold, it will not function properly. On the other hand, using excessively hot water can cause damage to your washing machine.
To determine the proper temperature, refer to the instructions on the packaging of your washing machine.
The coupling between the motor and the washer transmission is the motor coupling. When the washer is loaded beyond its capacity, the motor coupling will fail to protect both the motor and transmission.
Additionally, the motor coupling can fail due to normal wear. Inspect the motor coupling for damage. Replace the motor coupling if it is damaged.
The rotor and stator combine to generate a powerful electromagnetic field that rotates the tub in either direction.
The washer may not spin or agitate if the magnets on the rotor are damaged or if any part of the rotor is defective. Inspect the rotor for damage to determine if it is defective. Replace the rotor if it is damaged.
The stator and rotor combine to form a powerful electromagnetic field that rotates the tub in either direction.
The washer will not spin or agitate if the stator windings are damaged. Conduct a visual inspection of the stator for damaged windings or other defects.
Board of Motor Control
The motor is powered by the motor control board. If the motor control board is malfunctioning, the washer may not operate properly or at all.
To begin, visually inspect the control board for burned-out components.
To determine if the motor control board is defective, verify that it is powering the motor. If the control board is powered but is not powering the motor, it should be replaced.
Examine the agitator
The agitator is a critical component of the washing machine because it agitates the clothes and removes lint and dirt.
However, if the agitator is not functioning properly or is rusted, it will be unable to effectively break up the dirt. This could be the reason for your GE washing machine not spinning. As such, ensure that it is operating properly.
You can check it by removing the agitator rod and twisting it. If it easily comes out, it is functioning properly.
If removing it requires some effort, it is time to replace it. This is a simple repair that requires only a screwdriver. Components are readily available at most hardware stores.
Check the fabric type
If you’re using a powder-type detergent and adding the recommended amount, but your washing machine still won’t spin, check the fabric type.
Different fabrics require varying amounts of detergent to be cleaned properly.
For instance, synthetic fabrics such as polyester and nylon require more detergent than natural fibers such as cotton or wool.
If you’re unsure of the fabric you’re using, bring some of your laundry to a laundromat or consult with friends or relatives who own sewing machines.
Verify the spin cycle is set to “Extended,” not “Standard” or “Quick.”
If it is not, you should make the necessary changes. The spin cycle has an effect on the efficiency with which your washer removes water and dirt from your clothes.
A longer spin cycle extracts more water and dirt from the system. As a result, your clothes will be cleaner. A shorter spin cycle, on the other hand, removes less water and dirt. This softens and fluffs the clothes, but may impart an odor.
If you use a fabric softener or an odor-fighting powder, you must use more of it or the clothes will retain their odor. Most people use the “Standard” spin cycle by default.
Examine the door gasket
When the door closes, this is a rubber or plastic ring that surrounds the interior of the door and prevents water from entering.
If the door gasket has a hole or crack, water will enter the washer, causing a variety of problems.
Check the Manual for the Washing Machine
The final thing you should do is check the manual for the washing machine. Ensure that you have it and that you read it.
You should be able to obtain all of the information you require there. Indeed, there may be additional details in the manual that you were unaware of. That concludes our discussion for the time being.
Hopefully, this has resolved your GE washer not spinning issue. If not, and you’re in the market for a new washing machine, here’s a list of washing machine brands to avoid that you should be aware of before making a purchase.
I hope you found this list beneficial. Bear in mind, however, that a washing machine can fail in an infinite number of ways.
Regardless of how meticulously you maintain your household appliances, something will almost always go wrong. And when it does, it will cause you considerable inconvenience and may even cost you money.
That is why, if you are unable to comprehend the issue, I recommend that you hire an experienced professional to perform all maintenance for you.